CONDUCTIVITY ANALYSER
|
JENCO
STARTING
AT $529.00 | |
|
Conductivity analyzer, 1/4 DIN panel mount
single parameter analyzer with an IP-65 case,
and selectable 2 or 4- wire cells. Has
programmable reference temperature and
coefficients. The 4-20 mA output is fully
programmable, reversible and isolated. There are
2 programmable relays for conductivity and one
relay for temperature and an RS-485 interface.
Password & ID protected. Graphical display.
CE approved. 115/230V AC.
|
|
|
JENCO
6308CT |
Advance Multi Parameter Analyzer-Conductivity, TDS,
Temperature |
$529.00 |
|
PROBES
AVAILABLE |
|
JENCO
C621-1-4-2 |
Cell
constant K=0.01. 3/4 Inch MNPT Front thread
only, 316 Stainless Steel Probe, Teflon insulator,
20 foot long cable.
**For use with Ultra Pure Water as in steam
generation plants |
$222.00 |
|
JENCO
C621-2-4-2 |
Cell
constant K=1.0. 3/4 Inch MNPT Front thread
only, 316 Stainless Steel Probe, Teflon insulator,
20 foot long cable.
**For
General Purpose use Potable Water, Wastewater |
$222.00 |
|
|
FEATURES |
|
|
Bumpless Calibration
|
|
CE Approved
|
|
RS-485 Output
|
|
Programmable Relays For Conductivity
|
|
Reversible And Isolated 4 To 20mA Output
|
|
Programmable Relay For Temperature
|
|
Conductivity/Temp.Measurement & Control
|
|
Simultaneous Analysis And Display For
Measurement And Controls |
|
User Programmable Reference Temperature
Temperature Coefficient |
|
Selectable 2-Wire Or 4-Wire Cells For Long
Cable Length & Wide Measurement Range
|
|
SPECIFICATIONS |
|
| |
|
|
|
| |
|
0 uS to 5.0 mS |
|
0.01 uS to 0.1 mS |
|
0.5% ± 1 LSD |
|
| |
|
0 ppm to 150.0 ppt |
|
0.01 ppm to 0.1 ppt |
|
0.5 % ± 1 LSD |
|
| |
|
-10.0 to 120°C |
|
0.1 °C |
|
± 0.1 °C |
| |
| |
Reference Temperature |
|
1.5 °C to 25.0 °C
|
| |
Temperature Coefficient |
|
0.0 % to 40.0%
|
| |
Basic Cell Constant |
|
0.01,1 and 10.0
|
| |
Cell Constant Range |
|
±30% of Basic Cell Constant
|
| |
| |
Output Relays numbers |
|
Two Programmable High or Low Relays
for Conductivi |
| |
Control Type |
|
On/Off
|
| |
Relay Output (Resistive Load
Only) |
|
5 Amps at 115 VAC, 2.5 Amps at 230
VAC |
| |
Relay Set Point Hysteresis |
|
User Programmable
|
| |
| |
Current Output |
|
Isolated 4 to 20 mA
|
| |
Range |
|
Selectable Zero, & Span
|
| |
Accuracy |
|
± 0.02mA
|
| |
Isolated Voltage |
|
500 VDC
|
| |
Maximum Load |
|
500 Ohms
|
| |
| |
ATC Sensor |
|
Thermistor 10KiloOhms at 25 °C
|
| |
Security Protection |
|
4 digit password
|
| |
Keypad |
|
Audio feedbackup
|
| |
Communication |
|
RS-485
|
| |
Display |
|
Graphic LCD w/Backlight
|
| |
Power source |
|
115/230 VAC ,50/60Hz
|
| |
Dimensions |
|
1/4 DIN ,Depth 148 mm
|
| |
Weight |
|
950 gm
|
|
|
PATHFINDER
INSTRUMENTS
Order or Shop On Line